Chevron Left
Retour à Sensor Manufacturing and Process Control

Avis et commentaires pour d'étudiants pour Sensor Manufacturing and Process Control par Université du Colorado à Boulder

4.6
étoiles
187 évaluations
42 avis

À propos du cours

"Sensor Manufacturing and Process Control" can also be taken for academic credit as ECEA 5343, part of CU Boulder’s Master of Science in Electrical Engineering degree. This is our fourth course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled "Sensors and Sensor Circuits", our second course entitled "Motor and Motor Control Circuits", and our third course entitled "Pressure, Force, Motion, and Humidity Sensors". Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. Our second and third courses give you three hands-on lab experiments using the kit. This third course assumes that you already know how to use the kit. You will learn about sensor signal characterization and manufacturing techniques and how to optimize the accuracy of sensors. You will also learn about more advanced sensors, proportional-integral-derivative (PID) control, and how this method is used to give you a closed loop sensor feedback system. After taking this course, you will be able to: ● Understand how sensor manufacturers characterize and calibrate their sensors. ● Tune a PID control loop and access the PID control function of the Cypress PSoC development kit for a motor control application. ● Understand manufacturing methods used to build electro-mechanical and micro-machined sensors. You will need to buy the following components to do the two course projects based on the videos in this module. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. Or, you may obtain the specs from the site, and purchase them elsewhere. All are quantity one except for N107-ND where you need three, and 493-15371-ND where you need two. 428-3390-ND P14355-ND FQU13N10LTU-ND N107-ND 1N5393-E3/54GICT-ND RNF14FTD1K00CT-ND P0.62W-1BK-ND 493-15371-ND Additional equipment needed: • Wire - various gauges and lengths • Breadboard • Oscilloscope – suggested models are: o PICOSCOPE 2204A-D2 available on www.digikey.com or o Digilent 410-324 | OpenScope MZ available on www.newark.com Depending on your budget, you can also investigate these models: o Hantek HT6022BE20MHz - https://www.amazon.com/dp/B009H4AYII o SainSmart DSO212 - https://www.amazon.com/dp/B074QBQNB7 o PoScope Mega50 USB - https://www.robotshop.com/en/poscope-mega50-usb-mso-oscilloscope.html o ADALM2000 - https://www.digikey.com/en/products/detail/analog-devices-inc./ADALM2000/7019661...

Meilleurs avis

KM
15 nov. 2020

Great course to learn about\n\nSensor Manufacturing and Process Control in details.I highly recommend this course and thank you all.

GQ
12 avr. 2021

This program is exceptional and really practical. Challenging computations in Process Control and Instrumentation .Awesome

Filtrer par :

1 - 25 sur 45 Avis pour Sensor Manufacturing and Process Control

par Guillaume V

17 mai 2020

I have learned a lot with this sensor specialization. Some selected application notes part from the reading material are very worth the time spent. The view is broad, sensor circuits, MEMS manufacturing techniques, etc. It helps me progress, better understand what I have seen in my career so far in the aerospace, electrical and medical industries.

par G . p

6 juin 2020

This video session is very useful to learn both theoretical and practical

par Bhargav c

28 juil. 2020

good one

par AKBAR A P

13 oct. 2020

Good👍

par Ngo T D

13 mars 2021

Great course, great content and learning material. It has real lab exercises with careful instructions. You can still do the assignment without real circuit, but learning by doing will be more efficient, and of course this subject needs real equipment.

The quiz is really helpful for each module lesson, but some of them are a bit difficult or having typing problem. Teachers should acknowledge and correct that. I hope lecture videos can have more animations about how devices work.

par AMALNATH M P

19 oct. 2020

Excellent Class and i learned more from here

par Nithis r k

21 sept. 2020

It's very useful

par Samriddhi V K

24 mai 2020

please increase the contents...Descriptions in presentation slides are not enough well to get clear understanding though we went through the referred text books and links

par Himanshu G

1 juin 2020

It was good.

par Parishi N

16 avr. 2020

some concepts in the first 2 weeks were not quite well explained

par Sheikh A M

2 juil. 2020

Instruction was not clear.

par Kasuntha M

16 nov. 2020

Great course to learn about

Sensor Manufacturing and Process Control in details.I highly recommend this course and thank you all.

par Geoffrey S Q

13 avr. 2021

This program is exceptional and really practical. Challenging computations in Process Control and Instrumentation .Awesome

par KARIMULLA S

21 août 2020

excellent ,we need more practice while solving the problem. material is very useful to answer the questions

par kishan n c

25 sept. 2020

have got a lot idea about industrial sensors and protocols and their construction theory

par Ashab U

17 mars 2021

This course is very effective for practical process control and instrumentation

par Elphus M

23 avr. 2021

i find it to be life changing course, it is ery interesting

Thanks

par Dean R

17 nov. 2019

Great course, well done. Lots of good information here

par Enrique V

20 juin 2020

This was the best course, I like the Labs :)

par Dr.Krushnasamy V S

4 juil. 2020

very toughest course.

But able to learn lot

par Adetifa O O

6 déc. 2020

Great course, now I know more on sensors

par MUHAMMED S P

18 oct. 2020

ക്ലാസ് വ്യത്യാസപ്പെട്ടിരിക്കുന്നു

par Abelardo J R B

18 août 2021

Excelente , todo muy dinámico.

par Likhith B N

21 sept. 2021

GOOD LEARNING EXPERIENCE

par Kaparthi U

15 mai 2020

It is very useful course