Retour à Pressure, Force, Motion, and Humidity Sensors
Avis et commentaires pour d'étudiants pour Pressure, Force, Motion, and Humidity Sensors par Université du Colorado à Boulder
214 évaluations
À propos du cours
"Pressure, Force, Motion, and Humidity Sensors" can also be taken for academic credit as ECEA 5342, part of CU Boulder’s Master of Science in Electrical Engineering degree.
This is our third course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled Sensors and Sensor Circuits. Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. This third course assumes that you already know how to use the kit.
After taking this course, you will be able to:
● Understand how to specify the proper AC or DC motor for a machine design.
● Integrate the motor to a machine, based on analysis of motor equations for voltage, current, torque and speed.
● Implement the motor and accompanying rotary sensor into a motor control circuit in both hardware and software.
● Add a motor and motor control circuit into a microprocessor based development kit.
● Create hardware and firmware to process motor feedback data to a microprocessor for further evaluation.
After taking this course, you will be able to:
● Understand how to specify the proper pressure, force, strain, position, motion, acceleration, occupancy, and humidity sensors for taking real-time process data.
● Implement these sensors into an embedded system in both hardware and software.
● Add the sensor and sensor interface into a microprocessor based development kit.
● Create hardware and firmware to process sensor signals and feed data to a microprocessor for further evaluation.
In this course you will build the circuit from Video 7 (Lab Exercise on strain gauges), Module 2 (Force and Strain Sensors and Touch Screens), and use it to make screen shots of the timing of the switch. If you haven't already wired up the system and written all the software per the instructions of Video 7, please do so now.
You will need to buy the following components to complete this assignment. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again.
These parts may be purchased off the Digikey web site, www. Digikey.com. One part needs to be purchased off the Sparkfun website www.sparkfun.com. Or, you may obtain the specs from the site, and purchase them elsewhere.
Digikey Part numbers are typed out here:
428-3390-ND
CF14JT22K0CT-ND
CF14JT100KCT-ND
Table shown here:
Index Quantity Part Number Description
1 1 428-3390-ND PSOC 5LP PROTOTYPING KIT
2 2 CF14JT22K0CT-ND RES 22K OHM 1/4W 5% AXIAL
3 1 CF14JT100KCT-ND RES 100K OHM 1/4W 5% AXIAL
Sparkfun part numbers are typed out here:
TAL221
Table shown here:
Index Quantity Part Number Description
1 1 TAL221 Mini-load cell - 100g, straight bar
Additional equipment needed:
• Wire - various gauges and lengths
• Breadboard
• Oscilloscope – suggested models are:
o PICOSCOPE 2204A-D2 available on www.digikey.com or
o Digilent 410-324 | OpenScope MZ available on www.newark.com
Depending on your budget, you can also investigate these models:
o Hantek HT6022BE20MHz - https://www.amazon.com/dp/B009H4AYII
o SainSmart DSO212 - https://www.amazon.com/dp/B074QBQNB7
o PoScope Mega50 USB - https://www.robotshop.com/en/poscope-mega50-usb-mso-oscilloscope.html
o ADALM2000 - https://www.digikey.com/en/products/detail/analog-devices-inc./ADALM2000/7019661
Meilleurs avis
BJ
14 août 2022
Great introduction course to sensors. I really enjoyed the instructors videos as they were clear and engaging. I would recommend it.
TH
27 août 2020
This course is very interesting. I completed this course.But I can not get my certificate.Please help me to earn my certificate.
Filtrer par :
1 - 25 sur 48 Avis pour Pressure, Force, Motion, and Humidity Sensors
par JiaJie, X
•15 juil. 2020
par Paul P
•9 avr. 2020
par Pablo C S
•12 nov. 2019
par HET V B
•28 juil. 2020
par Amit A
•5 juil. 2020
par Vinsensius C F
•1 mai 2020
par Enrique V
•29 mai 2020
par MR. V S
•12 mai 2020
par Abhishek K
•10 mai 2020
par Mr.KAUSTUBH K S
•21 avr. 2020
par Bonifasius B S A
•16 mai 2020
par Ngo T D
•4 mars 2021
par Guillaume V
•3 avr. 2020
par Brittany j
•15 août 2022
par Theint Z H
•28 août 2020
par Kasuntha M
•11 nov. 2020
par Sachin G
•3 nov. 2020
par Nimisha M
•23 déc. 2020
par KARIMULLA S
•3 août 2020
par Pankaj R
•20 sept. 2022
par Ganesh R P
•23 juin 2020
par Neredikomma S R
•12 juin 2020
par Yared B
•28 janv. 2021
par Jos� R
•2 août 2020
par P S K R
•12 juin 2020
Coursera Footer
© 2022 Coursera Inc. Tous droits réservés.
